Hotpoint GX641FGK Instrukcja Obsługi Pobierz pdf (Strona 5)

• Where the hob is not installed over a built-in oven, a wooden panel must

be installed as insulation. This must be placed at a minimum distance of

20 mm from the lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet must be

removed. It is advisable to install the oven so that it rests on two strips of

wood, or on a completely at surface with an opening of at least 45 x 560

mm (see diagrams).

560 mm.

45 mm.

! The hob can only be installed above built-in ovens with a cooling ventilation

system.

Electrical connection

! The supply cable must be positioned so that it never reaches at any point

a temperature 50°C higher than the room temperature. The cable must be

routed away from the rear vents. Should you require it, you may use a longer

cable, however, you must ensure that the cable supplied with the appliance

is replaced by one of the same specications in accordance with current

standards and legislation.

Your appliance is supplied with a 13 amp fused plug that can be plugged into

a 13 amp socket for immediate use. Before using the appliance please read

the instructions below.

! THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A

QUALIFIED ELECTRICIAN.

Replacing the fuse

When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362

should always be used, and the fuse cover re-tted. If the fuse cover is lost,

the plug must not be used until a replacement is obtained.

Replacement fuse covers

If a replacement fuse cover is tted, it must be of the correct colour as

indicated by the coloured marking or the colour that is embossed in words

on the base of the plug. Replacements can be obtained directly from your

nearest Service Depot.

Removing the plug

If your appliance has a non-rewireable moulded plug and you should wish

to remove it to add a cable extension or to re-route the mains cable through

partitions, units etc., please ensure that either:

• the plug is replaced by a fused 13 amp re-wireable plug bearing the BSI

mark of approval.

or:

• the mains cable is wired directly into a 13 amp cable outlet, controlled by a

switch, (in compliance with BS 5733) which is accessible without moving

the appliance.

Please note: for appliances with a rating greater than 13 amp (eg: electric

hob, double ovens and freestanding electric cookers etc.) the mains cable

must be wired into a cooker output point with a rating of 45 amp. In this case

the cable is not supplied.

Disposing of the plug

Ensure that before disposing of the plug itself, you make the pins unusable so

that it cannot be accidentally inserted into a socket. Instructions for connecting

cable to an alternative plug:

! The wires in the mains lead are coloured in accordance with the following

code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

If the colours of the wires in the mains lead do not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked “E” or or coloured Green

or Green & Yellow.

Connect Brown wire to terminal marked “L” or coloured Red.

Connect Blue wire to terminal marked “N” or coloured Black.

If a 13 amp plug (BS 1363) is used it must be tted with a 13 amp fuse. A 15

amp plug must be protected by a 15 amp fuse, either in the plug or adaptor

or at the distribution board. If you are in any doubt about the electrical supply

to your machine, consult a qualied electrician before use.

How to connect an alternative plug

The wires in this mains lead are coloured in accordance with the following code:

BLUE “NEUTRAL” (“N”)

BROWN “LIVE” (“L”)

GREEN & YELLOW “EARTH” (“E”)

GREEN &

YELLOW

BROWN

BLUE

13 amp fuse

CROSS-BAR

CORD GRIP

Gas connection

The appliance should be connected to the main gas supply in compliance

with current national regulations. Before carrying out the connection, make

sure the cooker is compatible with the gas supply you wish to use: G20-

20mbar (Natural Gas).

! Check that the pressure of the gas supply is consistent with the values

indicated in Table 1 (“Burner and nozzle specications”). This will ensure the

safe operation and longevity of your appliance while maintaining efcient

energy consumption.

Connection with a rigid pipe (copper or steel)

! Connection to the gas system must be carried out in such a way as not to

place any strain of any kind on the appliance.

There is an adjustable L-shaped pipe tting on the appliance supply ramp

and this is tted with a seal in order to prevent leaks. The seal must always

be replaced after rotating the pipe tting (seal provided with appliance). The

gas supply pipe tting is a threaded 1/2 gas cylindrical male attachment.

1 2 3 4 5 6 7 8 9 10 11 12

Komentarze do niniejszej Instrukcji

Brak uwag

Hotpoint GX641FGK Instrukcja Obsługi Strona 5

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Płyty grzewcze Hotpoint GX641FGK